Online Double Conversion UPS — Complete Guide & APC vs Eaton Comparison

How the double conversion topology works, why zero transfer time matters, what SCVC means, IP ratings for harsh environments, and an honest APC vs Eaton comparison.

When someone says "I need an online UPS," they specifically mean a double conversion online UPS — the highest protection category available in the market. If you are protecting a server room, a medical imaging system, a telecom rack, a data centre row, or any process where even a 20-millisecond power interruption could cause a crash, a double conversion online UPS is the only topology that delivers the protection you need. This guide explains exactly how it works, what variants like SCVC mean, how to interpret IP protection ratings, and how the two leading brands — APC (Schneider Electric) and Eaton — compare in practice.

What is Online Double Conversion UPS?

The term "double conversion" describes a two-stage power conversion process:

  1. First conversion (AC → DC): The incoming mains AC supply is converted to DC by the rectifier (also called the charger). This DC bus simultaneously charges the battery bank and feeds the inverter.
  2. Second conversion (DC → AC): The inverter converts the DC bus back to clean AC power and delivers it to the connected load.

Because the load is always powered through this inverter — which is itself always running — there is zero transfer time when mains power fails. The battery simply takes over supplying the DC bus, and the inverter continues outputting uninterrupted AC to the load. There is no switching, no relay, no delay.

Why zero transfer time matters: Computer power supplies, server motherboards, and medical equipment can tolerate brief voltage dips but typically cannot tolerate a complete interruption of more than 4–8ms. Many cheap UPS units have transfer times of 10–20ms, which causes servers to reboot. An online double conversion UPS has 0ms transfer time — the load never sees the grid failure.

How Double Conversion UPS Works — Component by Component

Rectifier / Charger

The rectifier converts incoming AC (230V single-phase or 415V 3-phase) to regulated DC. Modern IGBT-based rectifiers have near-unity input power factor (0.99 on premium models), which means they draw clean sinusoidal current from the grid — important for facilities with generator backup, as generators are sensitive to non-linear loads. The rectifier also charges the battery bank to its float voltage while running the inverter.

Battery Bank / DC Bus

The battery bank connects directly to the DC bus. During normal operation it is kept fully charged at float voltage. When mains fails, the battery instantaneously becomes the sole power source for the DC bus with no switching event. The voltage on the DC bus remains constant throughout — the inverter never knows the difference between utility and battery power.

Inverter

The inverter converts DC to AC. It runs continuously regardless of whether the source is mains or battery. Because the inverter synthesises the output waveform from scratch, it delivers a perfect sine wave at the exact specified voltage and frequency — typically 230V ±1% and 50Hz ±0.1% — regardless of what the input supply looks like. This is why a double conversion UPS is immune to all mains power problems: voltage sags, surges, spikes, brownouts, frequency variations, and complete failures.

Static Bypass

Every online UPS includes a static bypass circuit — a solid-state switch that can connect the load directly to mains in the event of an overload or UPS internal fault. The bypass is managed automatically by the UPS microprocessor. Modern static bypasses switch in under 1ms. A manual maintenance bypass is also provided for safe servicing of the UPS without disconnecting the load.

Advantages of Online Double Conversion UPS

  • Zero transfer time (0ms): No power interruption under any failure mode
  • Complete electrical isolation: The output is entirely synthesised by the inverter — no grid noise, spikes, or surges reach the load
  • Constant voltage and frequency: Output is regulated regardless of input variations (typically ±1% voltage, ±0.1% frequency)
  • Protection against all eight power problems: Power failure, undervoltage (brownout), overvoltage, electrical noise, frequency variation, switching transients, harmonic distortion, and surges
  • Galvanic isolation: No direct electrical connection between input and output
  • Compatible with generators: Clean output even when powered from a generator with unstable voltage or frequency

Ideal applications for online double conversion UPS

  • Server rooms and data centres
  • Medical equipment (MRI, CT, ICU, OT)
  • Telecommunications (BTS, switch rooms)
  • Industrial control systems (PLC, SCADA, CNC)
  • Financial trading floors
  • Broadcast facilities

UPS Topology Comparison

Offline / Standby UPS

Load normally on raw mains. Switches to inverter on failure. Transfer time: 10–20ms. Lowest cost. Suitable only for basic PC protection.

Line-Interactive UPS

AVR (auto voltage regulation) on mains path. Inverter switches in on failure. Transfer time: 4–8ms. Good for small servers, home offices.

Online Double Conversion

Load always on inverter. Zero transfer time. Complete isolation. Perfect output quality. Best for data centres, medical, telecoms, industrial.

SCVC — What It Is and Which UPS Use It

SCVC stands for Static Contactless Voltage Conditioner (also sometimes called the "ECO conversion" mode in Eaton terminology). It is a topology introduced in some Eaton models — notably the Eaton 9SX and Eaton 9PX in ECO mode — that partially conditions the input voltage rather than performing a full double conversion, with the aim of improving efficiency.

In SCVC/ECO mode, when the input voltage is within a defined acceptable window (typically ±10% of nominal), the UPS bypasses the full rectifier-inverter circuit and instead uses a series transformer or boost/buck regulator to bring the voltage to the precise output specification. This reduces internal conversion losses and can achieve efficiencies of 97–99%, compared to 93–96% for full double conversion.

The critical difference: in SCVC mode, there is a brief switching event (typically 1–2ms) if the input suddenly falls outside the acceptable window and the UPS must switch to full inverter operation. For most IT loads this is acceptable, but for the most sensitive applications, some engineers prefer to disable ECO mode and run in pure double conversion at all times. Eaton allows this configuration choice via the UPS management interface.

UPS Enclosure Ratings — IP42 vs IP55

The IP (Ingress Protection) rating describes how well the UPS enclosure is sealed against solid particles and liquids, following the IEC 60529 standard. The two digits represent:

  • First digit: Protection against solid objects (0 = no protection, 6 = dust tight)
  • Second digit: Protection against liquids (0 = no protection, 8 = submersion)

IP42 — Standard Indoor UPS

IP42 means protection against solid objects larger than 1mm (wires, small screws, insects) and protection against vertically dripping water. This is the standard rating for most APC Smart-UPS, Eaton 5PX/9PX, and similar IT UPS units intended for server rooms, comms rooms, and clean office environments. IP42 is not suitable for environments with dust, humidity, or water spray.

IP55 — Industrial UPS

IP55 means protection against dust ingress sufficient to prevent harmful deposits, and protection against water projected as a jet from any direction. IP55-rated UPS units are built for factory floors, production lines, outdoor telecom cabinets, water treatment facilities, marine environments, and anywhere with high dust, humidity, or the possibility of water spray. The enclosure is typically powder-coated heavy-gauge steel with sealed cable glands.

Harsh Environment UPS

For the harshest environments — oil and gas facilities, offshore platforms, chemical plants, steel mills — a standard IP55 enclosure may not be sufficient. Industrial UPS for these applications typically include:

  • Conformal-coated PCBs (protective varnish coating to resist moisture and corrosive gases)
  • Extended operating temperature range (-10°C to +50°C vs standard 0–40°C)
  • EMC shielding to meet IEC 61000 industrial levels
  • Anti-vibration mounting
  • ATEX certification for explosive atmospheres (Zone 1/Zone 2) on specialist models

APC vs Eaton UPS — Which is Better?

As an authorised dealer for both APC (Schneider Electric) and Eaton, Sukhai UPS does not have a brand loyalty bias — we recommend what best fits the application. Here is our honest assessment:

APC by Schneider Electric

APC is the best-known UPS brand in the world, with the largest installed base. The Smart-UPS series (1–10 kVA, single phase) is the most widely deployed UPS in Indian server rooms and is excellent for IT protection. The Galaxy 300/5000 series covers 3-phase requirements from 10 kVA to 500 kVA. APC's main advantages are deep market penetration (meaning third-party support engineers and spare parts are widely available), excellent network management software (APC PowerChute), strong APC-authorised service centres across India, and high brand recognition that makes budget approvals easier.

Eaton

Eaton has a strong reputation in the industrial and data centre segments. The 9PX (1–22 kVA, single phase) and 93PM/93PR (3-phase modular) series are technically excellent, with class-leading efficiency ratings. Eaton's ABM (Advanced Battery Management) charging algorithm extends battery life by preventing chronic over-charging — a real differentiator in hot climates. The 93PM modular architecture (15 kVA to 1.5 MW in a single frame) is preferred by many data centre designers for its scalability and N+1 redundancy options. Eaton's service network in India is growing but is not as extensive as APC's outside of major metros.

APC Smart-UPS 3000 vs Eaton 5PX 3000 — Comparison

Specification APC Smart-UPS 3000VA Eaton 5PX 3000VA
Rated VA / Watts3000 VA / 2700 W3000 VA / 2700 W
TopologyOnline Double ConversionLine-Interactive (online mode optional on some models)
Transfer time0ms (online)8ms (line-interactive) / 0ms (online models)
Efficiency (normal)~93%~98% (ECO mode)
Battery type12V SMF VRLA (internal)12V SMF VRLA (internal + ext. battery option)
CommunicationUSB, RS-232, SmartSlotUSB, RS-232, network card slot
Mgmt softwarePowerChute Network ShutdownEaton IPM (Intelligent Power Manager)
Form factorTower / 2U rackTower / 2U rack
Approx. price (India)₹60,000–75,000₹65,000–80,000

Which Brand Should You Choose?

  • Choose APC if: you are an office/SMB customer, you want the widest third-party support network, you need standardisation across a large installed base, or budget approvals are easier with a recognisable brand.
  • Choose Eaton if: you need industrial-grade reliability, you want better efficiency (lower running costs at scale), you need modular 3-phase for a data centre, or if ABM battery management in a hot climate is a priority.
  • Both are excellent for any standard UPS application. The difference in real-world reliability between a properly specified and maintained APC and Eaton unit of the same class is negligible.

Popular Online UPS Models Available from Sukhai UPS

  • APC Smart-UPS (single phase, 1–10 kVA): The industry workhorse for IT rooms, server closets, and comms rooms. Available in tower and rack form factors.
  • APC Galaxy 300 / Galaxy 5500 (3-phase, 10–500 kVA): Large-scale data centre and industrial protection. Modular options available.
  • Eaton 5PX (single phase, 1.5–3 kVA): Compact, high-efficiency line-interactive with optional online operation. Popular for small IT rooms.
  • Eaton 9PX (single phase, 2–22 kVA): Online double conversion with SCVC ECO mode. Excellent for medium-sized server rooms.
  • Eaton 93PM (3-phase modular, 15 kVA to 1.5 MW): Hot-swappable power modules, ideal for data centres needing N+1 redundancy and future scalability.
  • Emerson / Vertiv Liebert GXT5 (single phase, 1–10 kVA): Reliable double conversion from Vertiv. Good alternative where APC/Eaton are not preferred by the client.

FAQs — Online Double Conversion UPS

An online UPS means the load is permanently powered through the UPS inverter — it never switches. Mains power feeds the rectifier (AC to DC), the DC bus powers both the battery and the inverter, and the inverter continuously supplies the load. There is zero transfer time and complete electrical isolation from the grid.
SCVC stands for Static Contactless Voltage Conditioner. It is used in some Eaton models to partially condition input voltage rather than performing full double conversion, improving efficiency to 97–99%. If input voltage falls outside acceptable limits, it switches automatically to full double conversion.
IP42 is standard indoor protection — against objects >1mm and vertical water drips — suitable for server rooms. IP55 is for industrial environments — dust-resistant and waterjet-protected — required for factory floors, outdoor cabinets, and marine installations.

Talk to Sukhai UPS About Your Online UPS Requirement

Sukhai UPS is an authorised dealer for APC, Eaton, and Emerson online UPS systems, covering single-phase and 3-phase requirements from 1 kVA to 500 kVA+. We provide supply, installation, commissioning, and ongoing AMC support. Our engineers will help you select the right topology, kVA size, and battery configuration for your specific application.

Call +91-98208-43000 or browse our UPS Systems page. We serve Mumbai, Thane, Pune, and all major cities across India.

Get a Quote for Online UPS Supply & Installation

APC, Eaton & Emerson double conversion UPS — 1 kVA to 500 kVA. Sukhai UPS covers Mumbai, Thane, Pune, Navi Mumbai and all major cities.

+91-98208-43000 WhatsApp Us